Hirschmann MM20-Z6Z6Z6Z6SBH | 4-Port SFP Media Module, In Stock

  • Model: MM20-Z6Z6Z6Z6SBH
  • Brand: Hirschmann (Belden Industrial Solutions lineage)
  • Series: MICE Media Module — MM20 family
  • Core Function: Plugs into an MS20/MS30 chassis backplane and hands you four SFP slots, so you can grow fiber links without touching the host switch.
  • Type: Media Module (not a standalone switch)
  • Key Specs: 4 × SFP slots; 10/100 Mbit/s class module; hot-swappable on the host backplane
Category:

Description

Key Technical Specifications

Parameter Specification
Model MM20-Z6Z6Z6Z6SBH
Module Type MICE media module for MS20 / MS30 modular switches
Ports 4 × SFP slots
Port Speed 100 Mbps class; actual rate depends on the SFP transceiver installed
Media Fiber, multi-mode or single-mode — determined by the SFP, not the module
Hot Swap Yes — replace on the host backplane without powering down the switch
Power Drawn from the MS20/MS30 host backplane; no external supply
Operating Temperature 0 °C to +60 °C is the standard MM20 rating; “S” suffix denotes the 0…+60 °C range
Management Managed through the host switch — Web / SNMP / CLI
Mounting Inserts into an MICE MS20/MS30 module slot
Communication None of its own; it is a media layer extension
Certification Suffix-dependent (cUL508 / cUL1604 Class 1 Div. 2 variants exist) — verify with OEM datasheet

 

Product Introduction

A plant wants four new fiber runs to a remote building. The MS30 in the control room has the ports, but no free slots filled with optics. Somebody suggests replacing the whole switch. That’s a two-day outage for a two-hour job — and the answer is a media module like this one.The MM20-Z6Z6Z6Z6SBH is a four-slot SFP carrier for Hirschmann’s MICE MS20/MS30 chassis. Its real value is that you buy ports, not switches. Need single-mode instead of multi-mode? Swap the SFP, not the module. Need to add a link? Insert a transceiver, not a new chassis. The hot-swap design means a failed module comes out and a spare goes in while the host keeps running — I’ve done that swap in under ten minutes on a live line.One subjective note: the “SBH” suffix is not interchangeable with “SAHH” or “EAHH.” Those letters encode temperature range and certification, and a mismatched suffix can mean a module rated for 0…+60 °C landing in a −40 °C outdoor cabinet. Read the old nameplate.

Quality SOP & Tech Pitfalls

The Lab Report (SOP)

  1. Nameplate and suffix check — confirm the full code, including the trailing letters, and rule out lookalikes like SAHH or EAHH.
  2. Visual inspection — connector pins, backplane edge contact, no cracked housing or re-soldered parts.
  3. Live test in a known-good MS20/MS30 host — verify backplane recognition, port LEDs, SFP detection, and link negotiation.
  4. Supply and continuity checks with a Fluke multimeter on the host feed.
  5. Firmware / software version of the host logged with the module serial.
  6. Anti-static sealing; test record attached.

The Engineer’s Warning (Pitfalls)The number one mistake is treating this as a standalone switch. It has no power input, no management IP, and no brain. It is a media layer riding on a host backplane. Install it on a bench expecting a web interface and you’ll waste an afternoon.The second is speed assumption. Z6 slots on this platform are 100 Mbps class. Drop a gigabit SFP in and it will either refuse to link or link at the wrong rate. I once watched a maintenance tech chase a “faulty module” for three hours; the SFP was a 1G part in a 100M slot. The module was fine.Third: hot-swap is real, but it is not license to yank modules during a ring failover. Do it in a quiet window.

 

Installation & Configuration Guide

Phase 1 — Pre-Installation (⚠️)

  1. Confirm the host switch is an MS20 or MS30 with a free media module slot. This module will not fit other chassis.
  2. Photograph the existing module’s nameplate and the host’s slot map before removing anything.
  3. If the slot is occupied, note which ports belong to that module — you will lose those links during the swap.

Phase 2 — Removal

  1. Release the module retaining screws or latches.
  2. Withdraw the module straight out along the rails. Do not pry against the backplane connector.
  3. Inspect the slot for dust, bent pins, or discoloration. Clean before inserting the replacement.

Phase 3 — Installation

  1. Verify the suffix on the new module matches the old one — temperature range and certification live in those letters.
  2. Slide the module in until the backplane connector seats fully; fasten the retaining hardware.
  3. Install the SFP transceivers. Match the SFP speed class to the slot — 100 Mbps SFPs for this Z6 module.
  4. Seat each SFP until the latch clicks; connect fiber with the correct polarity (TX to RX).

Phase 4 — Power-On & Testing

  1. Watch the host’s port LEDs for the new module’s ports — link and activity should come up within seconds.
  2. Log into the host switch (Web / SNMP / CLI) and confirm the module and all four ports are recognized.
  3. Check link state, negotiated speed, and error counters on each port.
  4. If the host runs a ring (HIPER-Ring / RSTP), confirm redundancy recovered after the swap.
  5. Record the module serial and host firmware version in the asset file.

Compatible Replacement Models

  • ✅ Drop-in Replacement: Another MM20-Z6Z6Z6Z6SBH. Identical suffix, identical behavior. Price varies with source; new-surplus commands a premium over pulls.
  • ⚠️ Software Compatible: MM20-Z6Z6Z6Z6SAHH or MM20-Z6Z6Z6Z6EAHH. Same port layout, different temperature/certification suffix. Verify the ambient rating matches your installation before accepting — budget 1–2 hours for documentation review and a bench test.
  • ❌ Hardware Mod Required: MM30-series modules (e.g., MM30-O7O7O7O7) or a fixed-port RS-series switch. Different module class or a different product entirely. Only consider these if you are doing a full network refresh, not a single-module replacement.

 

Frequently Asked Questions (FAQ)

Is this a switch?
No. It is a media module. No IP address, no power terminal, no management interface. It only works inserted in an MS20 or MS30 host.Can I hot-swap it?
Yes — that is the point of the MICE design. The host keeps running while you pull the module. Just avoid doing it during a ring failover or a critical data window.Will gigabit SFPs work in it?
Treat that as a no. Z6 on this platform is a 100 Mbps class slot. Use 100 Mbps SFPs unless the OEM datasheet for your exact suffix says otherwise.Does the suffix matter?
Yes. SBH, SAHH, and EAHH are not interchangeable — they encode temperature range and certification. A module rated 0…+60 °C does not belong in a −20 °C outdoor cabinet.Which SFPs should I buy?
Multi-mode 850 nm for short runs, single-mode 1310/1550 nm for long runs. The module does not care; the transceiver sets the distance and wavelength. Match the far-end transceiver.What’s the warranty?
Twelve months against manufacturing and functional defects — backplane recognition, port link, SFP detection. It does not cover a module installed in the wrong chassis or a mismatched SFP.Do you have the OEM manual?
The MICE MS20/MS30 user manual is the authority; I supply the rating plate photo and my own test record with every unit. For scheme-critical parameters, the OEM manual has the final say.