KONGSBERG TRX32 303088 | Direct Replacement Factory Sealed PCB

  • Model: TRX32
  • Part Number: 303088 (also seen as 303088 TRX32 381-206651F)
  • Brand: KONGSBERG (Kongsberg Maritime / Kongsberg Defence & Aerospace)
  • Series: K-Chief / K-Pos DP distributed I/O family
  • Core Function: A 32-channel digital I/O board — it sits in a Kongsberg rack, reads field status signals, and drives control outputs. That’s the job.
  • Type: Digital I/O Module (PC Board, TRX 32.500 SR 3030AA)
  • Key Specs: 32 channels, 24 V DC backplane supply, dual-redundant K-Bus (CAN-based) — see warning, specs conflict
Category:

Description

Key Technical Specifications

Parameter Claimed Value Source Reliability
Part Number 303088 Confirmed (multiple listings)
Board Marking PC Board TRX 32.500 SR 3030AA Confirmed (parts catalog)
Brand KONGSBERG Confirmed
I/O Channels 32 (DI/DO configurable) Two resellers agree
Supply Voltage 24 V DC from backplane Two resellers agree
Communication Dual-redundant K-Bus (CAN-based) One reseller
Operating Temp −25 °C to +70 °C (marine grade) One reseller
Protection Conformal coated PCB, IP20 panel mount One reseller
OEM Datasheet Not located —

 

Product Introduction

Kongsberg marine spares are a special kind of headache. The part number looks precise, the reseller looks confident, and the spec sheet looks professional — until you install it and the board doesn’t behave anything like the document promised. I’ve been around K-Chief and K-Pos DP panels long enough to know that the TRX32 designation covers a specific board family, and the 303088 suffix is Kongsberg’s internal manufacturing/revision code — it may indicate hardware version, conformal coating level, or marine certification batch.What I can tell you with confidence: this is a 32-channel digital I/O board from the Kongsberg maritime automation family, it’s obsolete, and it’s still circulating in the surplus market. Engineers buy it because a vessel’s automation system is down or a dry-dock window is closing and the OEM won’t sell new. In that situation, the spec sheet is decoration. The nameplate photo is the deliverable. I’ve lost more hours to a wrong revision than to a dead board — get the photo before the PO.

Quality SOP & Tech Pitfalls

The Lab Report (SOP):

  1. Counterfeit/visual check — nameplate photographed against the customer’s old board; PCB inspected for re-soldered components, refilled capacitors, or relabeled casings.
  2. Live test on test rack — energize, confirm no smoke, no abnormal heat after 30 minutes.
  3. Insulation resistance + multimeter checks — Fluke 115 and 500 V megger across input/output isolation.
  4. Channel-by-channel I/O test — where the board type allows, verify each channel responds.
  5. Revision/serial logging — recorded on the packing slip.
  6. Anti-static sealing — ESD bag, desiccant, original box where available.

The Engineer’s Warning:Two mistakes dominate with Kongsberg marine spares.First, buying on the part number without confirming the board type. The reseller descriptions for this exact number disagree on whether it’s an I/O module, a transceiver, or a filter board. If you order a transceiver into a rack expecting an I/O board, the rack won’t configure — and you’ll find out during commissioning, not during procurement.Second, not photographing the old board. Settings on these boards live in DIP switches, jumpers, or a configuration that isn’t printed anywhere. I once watched a technician swap a Kongsberg I/O board without photographing the DIP settings. Correct part number. Wrong configuration. The system came up “healthy” and then dropped every third packet for six hours. Photograph the old board — all sides, settings visible — before you remove it.

 

Installation & Configuration Guide

⚠️ Pre-Installation (10 min)

  1. Confirm the system is safe. Lockout/tagout the rack power supply, not just the board.
  2. Wait for capacitor discharge — 5 minutes minimum on legacy Kongsberg hardware.
  3. Photograph everything: old board nameplate (all sides), connector wiring, DIP switch/jumper positions, and the rack slot number. This one step prevents most startup failures.

Removal (5 min)
4. Label every wire with tape and marker. Don’t rely on color codes in an old panel.
5. Release the DIN rail or rack clips slowly. Old plastic goes brittle.
6. Pull straight out. Don’t rock the card — bent connector pins aren’t recoverable in the field.Installation (10 min)
7. Copy the DIP switch and jumper settings from your photos onto the new board BEFORE inserting it. Skipping this is the single most common cause of post-swap failures.
8. Confirm the full part string matches, suffix characters included.
9. Seat the board firmly until the clips click. No partial insertion.Power-On & Testing (15 min)
10. Restore power. Watch the LED boot sequence and compare against the old board’s behavior.
11. Verify 24 V DC at the board terminals with a Fluke 115.
12. Confirm communication with the host controller. No timeouts, no error LEDs.
13. Log the serial and revision into your maintenance records.

Compatible Replacement Models

Model Tier Notes
TRX32 303088 (same, new surplus) ✅ Drop-in Replacement Only realistic option. Confirm suffix characters match your old board.
TRX32 other revisions ⚠️ Software Compatible Same family, different revision. Requires reconfiguration and possibly a re-test. Budget 2–4 hours.
Kongsberg 8100148 / 8100172 ❌ Hardware Mod Required Different series (analog/digital I/O). Different rack, different wiring. Only worth it on a full system upgrade.
Current Kongsberg I/O module ❌ Hardware Mod Required No drop-in path. Plan a system upgrade, not a swap.

 

Frequently Asked Questions (FAQ)

Q: Is this an I/O module, a transceiver, or a filter board?
A: Unknown — and that’s the honest answer. Reseller listings for this exact part number claim all three. One source describes a 32-channel digital I/O module; another a digital transceiver; another a filter module. Get the nameplate photo and settle it there.Q: Can I hot-swap this safely?
A: Depends on the system configuration. Kongsberg K-Chief systems support hot-swap for some module types, but not all. Check your OEM manual. If in doubt, isolate the rack power.Q: The reseller sent a spec sheet. Can I trust it?
A: No. I’ve seen this part number paired with specs for a completely different module. Trust the nameplate and the OEM manual, not the marketing page.Q: What if the settings don’t match my old board?
A: Stop. Don’t energize. Copy the DIP/jumper settings from your pre-removal photos first. A correct part number with wrong settings will still fail.Q: Do you have it in stock?
A: Multiple surplus channels list it, with quoted prices around USD 3,500. Quantity is limited — confirm before scheduling your dry-dock window.Q: What’s the warranty?
A: One year from shipment, covering non-human-caused failure. It does not cover damage from wrong-type installation, ESD, or incorrect supply voltage.Q: Who has the final say on specifications?
A: The OEM documentation and your old board’s nameplate. I couldn’t find a Kongsberg datasheet for this number and I won’t guess. If you have the original system manual, that’s your authority.