Key Technical Specifications

• Product Model: XV-440-10TVB-1-50
• Manufacturer: Eaton
• Product Type: HMI Touchscreen Display
• Display Size: 10.4 inches
• Resolution: VGA, 640 x 480 pixels
• Touch Technology: Infrared Touch
• Front Panel Protection: IP65 (IP20 rear)
• Communication Ports: Ethernet (10/100Base-T), RS232, CAN/easyNet, USB
• Operating System: Windows CE (License dependent)
• Mounting Style: Front Panel Embedded Installation
• Power Dissipation: 32 Watts

 

Product Introduction

The Eaton XV-440-10TVB-1-50 is a 10.4-inch HMI touchscreen panel designed for industrial automation control and operator interaction. It provides a centralized visual interface for monitoring real-time data, managing alarms, and controlling connected PLCs or SCADA systems.This unit features a VGA TFT color display with infrared touch technology and an IP65-rated front panel for resistance against dust and water. It includes multiple communication interfaces including Ethernet and RS232, and can optionally function as an HMI-PLC combo when the appropriate software licenses are installed. (Always confirm the exact software and PLC license requirements for your specific application, as the base hardware supports multiple configurations).

Installation & Configuration Guide

Preparation (10 min)
Verify the panel cutout dimensions match the 10.4-inch specification. Gather the provided mounting brackets, gasket, and a Phillips screwdriver. Ensure the 24 VDC power supply is rated for at least 32W continuous output.Removal (5–10 min)
Disconnect all communication and power cables from the rear. Release the front panel mounting clamps or unscrew the rear brackets. Push the panel forward gently to free it from the enclosure cutout.Installation (10 min)
Insert the Eaton XV-440-10TVB-1-50 into the panel cutout, ensuring the gasket is properly seated against the enclosure for IP65 sealing. Attach the mounting brackets and tighten evenly to avoid warping the frame. Reconnect Ethernet, serial, and power cables.Power-On & Test (10 min)
Apply 24 VDC power. Observe the boot sequence on the display. Verify the touchscreen responds to input by tapping the calibration or menu buttons. Confirm communication with the connected PLC or controller via the configured Ethernet or serial port.

 

Troubleshooting Quick Reference

• Screen is blank / no power: Verify 24 VDC is present at the rear terminals. Check the internal fuse if power is confirmed at the connector.
• Touch not responding accurately: Run the touchscreen calibration utility from the system menu. Clean the front glass surface; debris can interfere with infrared touch sensors.
• Communication lost: Verify Ethernet cable link LEDs are active. Confirm the IP address matches the controller’s subnet. Check serial wiring for correct TX/RX crossover.
• Display flickering or dim: Measure the supply voltage under load. Voltage drop below 20 VDC can cause display instability. Check for excessive heat near the panel.
• Software not loading: Verify the CompactFlash card is properly seated. A corrupted OS image may require reloading from the OEM media.

Dimensions, Mounting & Wiring Notes

• Size: 10.4-inch diagonal display; check OEM drawing for exact W×H×D cutout dimensions
• Mounting: Front panel embedded mount with included hardware; IP65 front seal requires proper gasket compression
• Wiring: Rear terminal block for power; RJ45 for Ethernet; DB9 for RS232; USB host/device ports for programming and peripherals

 

FAQ

Does this panel come with Windows CE pre-installed?
The operating system requires a valid license. Some units ship with the OS loaded, while others require field installation via CompactFlash. Verify the exact configuration with your supplier before ordering.Can I use this as a standalone PLC?
Yes, but only if the PLC runtime license (e.g., LIC-PLC-MXP) is installed. Without it, the XV-440-10TVB-1-50 functions strictly as an HMI display.Is the touchscreen capacitive or infrared?
This model uses infrared touch technology. It does not rely on pressure, so it works with gloves and is resistant to surface contaminants, but the bezel area must remain clear of obstructions.My old panel failed. Is this a direct drop-in replacement?
Mechanically, yes, if your existing cutout matches the XV400 10.4-inch specification. However, you must verify that the software project is compatible and that all required communication licenses are present.Can I replace the backlight?
The backlight is not a user-serviceable component. If the display is dim or uneven, the entire panel should be replaced to maintain IP65 integrity and warranty coverage.Do you test the touchscreen before shipping?
Yes. Every unit is powered on and the touch response is verified across the full display area before shipment. Communication ports are also tested for basic connectivity.