Key Technical Specifications

• Product Model: MOISTURE.IQ-1-6-1-1-1-0-0
• Manufacturer: GE Measurement & Control (Panametrics)
• Product Type: Multi-Channel Moisture & Oxygen Analyzer
• Channel Capacity: Up to 6 independent measurement channels
• Display Parameters: Dew/Frost Point (TP), Temperature (℃), Pressure (psig), Oxygen (ppb/ppm/%)
• Calibration Range: Standard +10 to -80°C; Ultra-low -50 to -100°C
• Accuracy: ±2°C (above -100°C); ±3°C (below -100°C)
• Operating Pressure: 5 µHg to 5000 psig (345 bar)
• Digital Communication: Ethernet, Modbus, RS232/485
• Power & Safety: Internal isolation for intrinsic safety; 1 Fault Status Alarm

Product Introduction

The GE MOISTURE.IQ-1-6-1-1-1-0-0 is a multi-channel process analyzer designed to monitor trace moisture, pressure, temperature, and oxygen in non-aqueous liquids and gases. It serves as the central monitoring hub for critical industrial processes requiring continuous, high-precision dew point tracking.This unit supports up to six independent channels, each capable of accepting MISP or M-Series thin-film alumina sensors. It features a real-time touchscreen interface displaying up to twelve parameters simultaneously, alongside built-in data logging and USB ports for program updates. (Always verify the specific sensor type paired with this analyzer, as MISP sensors store calibration data internally, while M-Series sensors require manual configuration).

 

Installation & Configuration Guide

Preparation
Ensure the installation site is away from corrosive materials like primary amines or strong acids. Gather a Phillips screwdriver, ESD strap, and the probe Calibration Data Sheets shipped with the sensors.Removal (5–10 min)
Power off the unit using the ON/OFF switch on the lower left back panel. Disconnect the Ethernet, RS485, and 4-20mA output cables. Unplug the moisture probe connectors and remove the rack mounting screws.Installation (10 min)
Align the new MOISTURE.IQ-1-6-1-1-1-0-0 into the 19-inch rack slot. Secure the mounting screws. Connect the moisture probes strictly according to the serial numbers on the Calibration Data Sheets. Plugging a probe into the wrong channel will result in incorrect data.Power-On & Test
Flip the ON/OFF switch. Watch for the GE monogram and the blue progress bar on the touchscreen. Once the measurement screen loads, verify that the automatic cooling fan activates if needed. Check the display to ensure all six channels are reading valid parameters.

 

Troubleshooting Quick Reference

• Screen shows “NO PROBE”: The unit has not been configured for the activated probe. Verify the correct probe type is selected in the configuration menu.
• Screen shows “CHANNEL NOT AVAILABLE”: The measurement module for this channel is not physically installed in the backplane.
• Screen shows “NOT AVAILABLE”: The selected mode or units require a sensor option not present (e.g., reading %RH without a temperature sensor).
• Erratic dew point readings: Check the sample system flow rate. Gas flow should not exceed 10,000 cm/sec, and liquid flow should not exceed 10 cm/sec.
• Fan running constantly: Normal operation. The automatic cooling fan activates as needed to maintain internal enclosure temperature.

Dimensions, Mounting & Wiring Notes

• Size (Rack Mount): 482 mm (W) x 133 mm (H) x 357 mm (D); Weight: 11.2 kg
• Mounting: Standard 19-inch rack mount, with optional tabletop, panel, or weatherproof enclosures.
• Wiring: Rear panel features DC power input, isolated 4-20mA analog outputs, and digital communication ports. All non-auxiliary inputs are intrinsically safe via internal energy-limiting circuits.

 

FAQ

Can I mix different types of moisture probes on this unit?
Yes. The MOISTURE.IQ supports both MISP and M-Series probes across its six channels. Just ensure each probe is assigned to the correct channel in the software configuration.I got a “CHANNEL NOT AVAILABLE” error. Is my unit broken?
Not necessarily. This message simply means the internal measurement module for that specific channel slot is not installed. If you need that channel, you will need to add the corresponding hardware module.Do you test the actual moisture sensors with this?
We test the analyzer’s electronics, communication outputs, and display functions. The moisture probes themselves are sold separately and must be calibrated in your specific process environment.How do I update the firmware?
Use the front-panel USB port. You can load new programs and update firmware directly from a standard USB flash drive without opening the enclosure.What gases will damage the sensor?
Avoid strongly acidic or basic materials, as well as primary amines. These will degrade the aluminum oxide sensor element. Verify your gas composition against the OEM chemical compatibility chart.Can this measure relative humidity?
Only if the connected probe includes the integrated temperature sensor option. Without the temperature input, %RH calculations cannot be performed.