Tel: 
Email: 
WhatsApp: Description
Key Technical Specifications
| Parameter | Specification |
|---|---|
| Manufacturer | GE Fanuc (General Electric) |
| Product Series | Genius I/O |
| Number of Circuits | 24 (12 Input / 12 Output) |
| Input Voltage | 5 / 12 / 24 VDC (Selectable) |
| Output Current (Max) | 0.5A per circuit, 12A total |
| Input Processing Time | 1.4 ms |
| Dimensions (H×W×D) | 112 mm × 90 mm × 224 mm |
| Weight | 1.8 kg (4 lbs) |
| Operating Temperature | 0°C to 60°C |
Product Introduction
The IC660TBD024K is a terminal component designed for the GE Genius I/O system. It serves as an interface between the field wiring and the I/O blocks, simplifying installation and maintenance by providing a centralized connection point. This component bridges the gap between the physical sensors/actuators and the electronic processing modules.Engineered for robust industrial environments, the IC660TBD024K is built to withstand typical industrial conditions such as humidity, shock, and vibration. It features a durable design and is compatible with specific I/O blocks (IC660BBD024) and electronic components (IC660EBD024) to ensure seamless system integration. The terminal block handles the physical termination of wires and the internal power distribution to the I/O circuits.
Installation & Configuration Guide
Phase 1: Preparation (10 min)
- Safety First: Disconnect all power to the control panel. Follow Lockout/Tagout (LOTO) procedures to prevent accidental startup.
- Verify Compatibility: Confirm that the IC660TBD024K is compatible with your existing I/O blocks (IC660BBD024) and electronic components (IC660EBD024).
- Gather Tools: You will need a Phillips screwdriver and possibly a multimeter to verify voltage levels.
Phase 2: Removal (5–10 min)
- Mark Wires: Before disconnecting anything, label all field wires connected to the terminal block for easy reconnection.
- Disconnect Power: Unplug the 24V DC power supply cable from the terminal block.
- Remove Screws: Loosen and remove the screws securing the terminal block to the DIN rail or mounting panel.
- Extract: Carefully pull the terminal block away from the mounting surface.
Phase 3: Installation (10 min)
- Mounting: Align the IC660TBD024K with the DIN rail or panel mounting holes. Slide it into place until it clicks or secure it with screws.
- Reconnect Power: Plug the 24V DC power supply back into the terminal block.
- Wire Reconnection: Connect the field wires to the appropriate terminals. Ensure wires are securely fastened under the screw heads.
- Check Configuration: Verify that the voltage select jumpers (if present) are set to the correct position for your application (5V, 12V, or 24V).
Phase 4: Power-On & Test (10 min)
- Visual Inspection: Look for any loose wires or obvious damage.
- Power Up: Restore power to the control panel.
- LED Check: Observe the status LEDs on the terminal block and connected I/O modules. A steady green LED typically indicates normal operation.
- Function Test: Cycle the inputs and outputs to verify that signals are being processed correctly through the terminal block.
Troubleshooting Quick Reference
| Symptom | Probable Cause | Corrective Action |
|---|---|---|
| No Power to I/O Modules | Loose Power Connection | Reconnect and tighten the 24V DC power cable. |
| Intermittent Signal Loss | Loose Field Wiring | Inspect and retighten all terminal screws on the IC660TBD024K. |
| Output Fault | Overcurrent Condition | Check the total load on the 12A output. Reduce the number of active outputs if necessary. |
| Input Noise | Electrical Interference | Ensure proper grounding and shielded cables are used for field wiring. |
| Communication Error | Improper Configuration | Verify the voltage select jumpers and ensure the terminal block is properly seated. |
Dimensions, Mounting & Wiring Notes
- Dimensions: 8.8 inches (W) x 3.5 inches (H) x 4.4 inches (D) (224mm × 90mm × 112mm).
- Mounting: The IC660TBD024K is designed for DIN rail mounting (35mm rail) or panel mounting using the provided hardware.
- Wiring: The terminal block uses screw-type terminals for field wiring. It supports 24 circuits (12 inputs and 12 outputs). Ensure you follow the wiring diagram in the user manual to avoid miswiring.
IC660TBD024K GE
FAQ
What is the difference between IC660TBD024K and IC660TBD024?
The “K” suffix typically denotes a specific revision or variant of the terminal block. It is crucial to verify that the physical dimensions and connector pinouts match your existing setup. Always cross-reference with the hardware manual to ensure full compatibility.Can I use this with a VersaMax CPU?
No. The IC660TBD024K is specifically designed for the GE Genius I/O system. It is not compatible with the VersaMax platform. You must use the appropriate terminal blocks designed for the VersaMax system (e.g., IC698TBD024).What voltage should I set the terminal block to?
The IC660TBD024K is designed to operate at 5V, 12V, or 24V DC. The specific voltage depends on your system requirements. You must configure the internal jumpers or switches to match the voltage of your I/O modules and power supply.Is this a new or used part?
This is typically listed as “New Surplus” or “Refurbished.” New surplus parts are unused units from the original manufacturer’s inventory, while refurbished parts have been tested and verified to function correctly.
