H51q-HRS B5233-2 997205233 | HIMA PES Central Controller
H51q-HRS B5233-2 997205233 | HIMA PES Central Controller - Image 2
H51q-HRS B5233-2 997205233 | HIMA PES Central Controller - Image 3
H51q-HRS B5233-2 997205233 | HIMA PES Central Controller - Image 4

H51q-HRS B5233-2 997205233 | HIMA PES Central Controller

  • Model: H51q-HRS B5233-2 (P/N: 997205233)
  • Brand: HIMA
  • Series: H51q / H41q Safety System
  • Core Function: Central equipment mainframe and chassis for HIMA PES safety controllers
  • Type: Industrial Safety System / PLC Chassis
  • Key Specs: 19-inch rack (5 units high), supports TMR architecture, SIL 3 certified, includes B5233-2 slot rack
Category: SKU: H51q-HRS B5233-2 997205233 HIMA

Description

Key Technical Specifications

Parameter Specification
Manufacturer HIMA
Part Number 997205233
Model H51q-HRS B5233-2
System Type Programmable Electronic System (PES)
Safety Rating IEC 61508 SIL 3 (up to SIL 4 in specific apps)
Architecture Fault-tolerant (TMR/QMR capable)
Form Factor 19-inch Rack, 5 Units High (5U)
Slot Configuration Central equipment slots + I/O expansion
Processor Memory Up to 1 MB Flash-EPROM (OS), 1 MB SRAM (Data)
Operating Temp -20°C to 60°C (Industrial Standard)

 

Product Introduction

The HIMA H51q-HRS B5233-2 (Part Number 997205233) is the structural mainframe and central controller unit for the HIMA H51q safety system. It acts as the “brain” of the safety installation, housing the central processing modules and providing the backplane for digital and analog I/O expansion.Designed for high-hazard process industries, this unit supports HIMA’s proprietary fault-tolerant architectures (such as TMR – Triple Modular Redundancy). This ensures that even if a processor or module fails, the system continues to operate safely without shutting down the process unnecessarily. It is physically built as a 5-unit high, 19-inch rack assembly, integrating the B5233-2 slot rack for modular component insertion.

Installation & Configuration Guide

Preparation (10 min)

  1. Verify Components: Ensure you have the H51q-HRS mainframe, the B5233-2 rack insert, and the necessary PES modules (CPUs, I/O).
  2. Safety Grounding: Ensure the control cabinet has a solid earth ground connection. Safety systems are sensitive to electrical noise.
  3. Tooling: Have a Torx driver ready for the rack mounting screws and an ESD strap for handling the internal modules.

Removal (5–10 min)

  1. Power Down: Isolate the 24VDC power supply to the HIMA rack.
  2. Cable Management: Label and disconnect the serial interface cables (ELOP II/PC connection) and fieldbus cables.
  3. Extraction: Unscrew the rack ears from the panel or sub-rack and slide the unit out. Note: The unit is heavy; use two hands.

Installation (10 min)

  1. Mounting: Slide the H51q-HRS into the 19-inch cabinet slot. Secure it with M6 cage nuts and washers.
  2. Module Insertion: Insert the B5233-2 modules (CPUs, Comms) into the central slots. Ensure the locking levers click into place.
  3. Wiring: Connect the power supply to the redundant power inputs (if equipped). Connect the ELOP II programming PC via the serial or bus interface.

Power-On & Test (10 min)

  1. Power Up: Apply 24VDC. The LEDs on the power supply and CPU modules should illuminate.
  2. Self-Test: Watch for the “Run” LED to turn solid green. A flashing red LED indicates a hardware fault or firmware mismatch.
  3. Software Handshake: Open the ELOP II software on the connected PC. Verify that the software detects the H51q controller and reads the hardware configuration.

 

Troubleshooting Quick Reference

Symptom Probable Cause Action
Red “Fault” LED Module mismatch or failure Check that the firmware version in ELOP II matches the hardware revision. Reseat the module.
No Power / LEDs Off Blown fuse or loose power Check the 24VDC input terminals. Verify the polarity (reverse polarity protection may have tripped).
Communication Error Serial/Bus cable fault Verify the ELOP II PC is connected to the correct COM port. Check baud rate settings (usually 9600 or 19200).
I/O Not Updating Backplane contact issue Remove and re-insert the I/O modules (e.g., F3231) to clean the connector contacts.

 

Dimensions, Mounting & Wiring Notes

  • Dimensions: The mainframe is a standard 19-inch width. The height is 5 Units (5U), which is approximately 222 mm.
  • Mounting: Designed for vertical mounting in a standard 19-inch equipment rack.
  • Wiring: The B5233-2 rack accepts 4-unit high 19-inch I/O modules (like the F3231). Ensure the bus connectors between modules are tightly secured to prevent data transmission errors.
H51q-HRS B5233-2 997205233 HIMA

H51q-HRS B5233-2 997205233 HIMA

FAQ

What is the difference between H41q and H51q?
The H51q (this model) is the larger, high-availability system designed for complex safety applications (ESD, F&G). The H41q is a smaller, cost-effective version for simpler safety tasks. They share similar programming environments (ELOP II) but differ in physical size and redundancy capabilities.What does the “997205233” number mean?
This is the specific HIMA part number (PN) for the H51q-HRS B5233-2 assembly. It is crucial for ordering exact replacements to ensure firmware and hardware compatibility.Can I use this for a standard PLC application?
Technically yes, but it is overkill. This is a Safety PLC (SIS) designed for SIL 3 environments (Oil & Gas, Chemical). It is programmed differently than a standard logic controller and requires safety-certified engineering practices.Why is the “BUSY” light flashing rapidly?
This indicates the processor is executing the user program or communicating with the ELOP II engineering station. If it flashes continuously without stopping, the system is running normally.Is the B5233-2 rack compatible with older HIMA systems?
The B5233-2 is specific to the H51q/H41q generation. It is not backward compatible with very old HIMA systems (like the H51 or H31 series) due to differences in bus architecture and physical slot dimensions.

Related products