Description
Key Technical Specifications
| Parameter | Specification | Field Note |
|---|---|---|
| Power Supply | 18–36 V DC (Nominal 24 V DC) | Keep ripple low; noisy 24V kills analog precision. |
| Power Consumption | 12 W (IP20) / 15 W (IP65) | Sizing the cabinet PSU? Give it headroom. |
| Load Cell Excitation | 0.5 A rms, 330 Hz | Pressductor technology, not strain gauge. |
| Max Cable Resistance | 10 Ω | Long sensor runs need thicker gauge wire. |
| Analog Inputs | 2 | Handy for external speed or dancer references. |
| Analog Outputs | 6 (Selectable V/I) | Configurable for drives, brakes, or recorders. |
| Digital Outputs | 4 | Use these for hardwired safety trips. |
| Communication | PROFIBUS-DP (RS485) | GSD file ABB_0717.GSD usually required. |
| Filter Time | 5, 15, 30, 75, 250, 750, 1500 ms | 5ms for fast transients; 750ms+ for noisy processes. |
| Operating Temp | +5 to +55 °C | Push it any hotter and the display washes out. |
| Protection Rating | IP20 (DIN-rail) / IP65 (Sealed) | IP65 is heavy; mount it securely. |
Product Introduction
I’ve lost count of the times a plant manager blamed the drive for a web break, only for me to find the tension controller was the real culprit. The ABB PFEA113 is the heavy hitter in their tension electronics lineup. Unlike the basic PFEA111 or 112, this beast handles up to 4 load cells simultaneously. That means you can sum or difference signals across a wide web, compensating for uneven rolls without hacking together external relays. It’s built for the harsh reality of paper mills, metal processing, and film extrusion.Why do I keep a spare on the shelf? Because it’s predictable. The ±0.1% accuracy isn’t just a marketing number; I’ve seen it hold 30-micron foil steady through brutal acceleration ramps. The 6 analog outputs let you feed the PLC, the brake, and a strip chart recorder all at once. Just a heads-up: the IP65 version is a brick. It weighs around 6 kg, so don’t just hang it on a thin DIN rail without support.
Quality SOP & Tech Pitfalls
The Lab Report (SOP)
Before anything ships, I run it through the wringer.
- Visual/Counterfeit Check: I inspect the PCB conformal coating and solder joints. If it looks like a cheap clone, it gets binned.
- Live Test: Powered via a regulated Fluke 115 setup. I verify the 24V DC draw doesn’t spike past 15W.
- Analog Verification: I inject a known mV signal into the load cell inputs and measure the analog outputs with a multimeter. If the linearity drifts, it fails.
- Comms Check: Ping it over PROFIBUS-DP to ensure the MAC address responds and the GSD file matches.
- Sealing: Anti-static bag, desiccant, and sealed.
The Engineer’s Warning (Pitfalls)
- The Grounding Trap: I once watched a cable plant burn through thousands of feet of copper because a contractor tied the shield drain wire to the neutral instead of a clean PE ground. The PFEA113 uses a 330 Hz excitation. If your ground loop picks up 60 Hz noise, your tension reading will dance. Keep signal wires shielded, twisted, and grounded at one end only.
- Filter Time Settings: The default filter might be too slow for fast start/stop cycles. I’ve seen operators crank the filter down to 5ms to “fix” a lag, only to have the controller chase mechanical vibrations and chatter the brake. Don’t touch the filter unless you know exactly what frequency you’re trying to kill.
Installation & Configuration Guide
Phase 1: Pre-Installation
⚠️ Lockout/Tagout the machine. Do not hot-swap this while the web is running unless you want a snapped line and a mess. Wait at least 5 minutes for the 24V DC capacitors to discharge.
Take a photo of the old unit’s wiring. I mean it. The terminal blocks look similar, but a swapped analog output pair will fry your drive’s input card.Phase 2: Removal
Label every wire. Use masking tape and a Sharpie. Release the DIN rail clips carefully; the IP65 version is heavy and will snap your plastic clips if you drop it.Phase 3: Installation
Mount the new PFEA113. Copy the DIP switch or jumper settings from the old unit. If the old one had a specific PROFIBUS address set via hardware (or even if it was software-set), document it. Seat the module firmly onto the DIN rail until it clicks.Phase 4: Power-On & Testing
Apply 24V DC. Watch the 2×16 character display. It should boot without error codes.
Check the analog outputs with your multimeter. Jog the machine slowly. Verify the tension reading scales correctly from 0 to 10V (or 4-20mA). If the reading is inverted, check your load cell wiring polarity before blaming the controller.
Compatible Replacement Models
| Compatibility Tier | Model | Engineering Note |
|---|---|---|
| ✅ Drop-in Replacement | PFEA113-20 / PFEA113-65 | Same hardware. Just ensure the IP rating matches your environment. IP20 for clean cabinets, IP65 for washdown areas. |
| ⚠️ Software Compatible | PFEA112 | Only supports 2 load cells. You’ll lose half your sensor inputs. Requires logic rework in the PLC. |
| ❌ Hardware Mod Required | PFEA122 | Uses PROFINET/EtherNet/IP instead of PROFIBUS. You’ll need new network cards and a complete rewiring of the comms loop. |
Frequently Asked Questions (FAQ)
Can I hot-swap this safely?
No. Not unless your specific cabinet design has isolated power and signal relays, which is rare. Pulling the module while the web is running will cause an immediate loss of tension signal, likely resulting in a web break or a hard trip. Lock it out.What’s the difference between the -20 and -65 versions?
It’s all about the enclosure. The -20 is a standard DIN-rail module meant for a clean, climate-controlled electrical room. The -65 is a sealed, heavy-duty brick (IP65/NEMA 4) designed to survive dust, humidity, and washdowns. They share the same internal electronics, but the -65 is bulkier.My tension reading is jumping around wildly. Is the controller bad?
Probably not. 9 times out of 10, it’s a grounding issue or a loose load cell connection. Check your shield grounds first. If the mechanical web is vibrating, you might need to increase the digital filter time (try 75ms or 250ms) to smooth out the noise.Does it support Modbus TCP?
The standard PFEA113 relies on PROFIBUS-DP for fieldbus communication. If you need Modbus TCP or PROFINET, you should be looking at the PFEA122, or you’ll need an external protocol gateway.How long is the warranty on your surplus units?
I typically offer a 1-year warranty on my tested surplus stock. It covers dead-on-arrival (DOA) and functional failures under normal industrial use. It doesn’t cover units fried because someone hooked 110V AC to the 24V DC input.




Tel:
Email:
WhatsApp: 
