Tel: 
Email: 
WhatsApp: Description
Key Technical Specifications
| Parameter | Specification |
|---|---|
| Part Number | 1SFA619550R1071 |
| Type Designation | CE4T-10R-11 |
| Contact Configuration | 1 NO + 1 NC (Double Pole Single Throw – DPST) |
| Reset Method | Twist to Release |
| Actuator Type | Mushroom Head, 40mm Diameter |
| Color | Red Actuator on Black Bezel |
| Protection Class | IP66, IP67, IP69K (High Pressure/Temperature Washdown) |
| Material | Polycarbonate (Black Plastic) |
| Mounting Hole | 22.5 mm Diameter |
| Operating Temp | -25°C to +70°C |
| Certification | UL, CSA, EN60947-5-1 |
Product Introduction
If you work in food processing or anywhere that uses high-pressure washdowns, you know that standard buttons don’t last. The ABB 1SFA619550R1071 is built specifically for those harsh environments. It’s part of the Compact series, which means it’s a sealed unit—you can’t swap out individual contact blocks, but you gain a massive amount of durability because there are fewer seams for water and grime to penetrate.The standout feature here is the IP69K rating. That isn’t just marketing fluff; it means this switch can survive direct high-pressure, high-temperature spray. I’ve seen these mounted on packaging machines where they get blasted with steam daily, and they keep clicking while cheaper switches corrode internally. The “Twist to Release” mechanism is standard, but the 40mm mushroom head makes it an easy target for an operator to hit in a panic. It’s a simple device, but when safety is on the line, simple and rugged is exactly what you want.
Quality SOP & Tech Pitfalls (The Reality Check)
The Lab Report (SOP)
Even though it’s a simple switch, we verify every unit before it goes out:
- Visual Inspection: We check the polycarbonate housing for stress cracks, especially around the mounting threads. We also ensure the red mushroom head isn’t faded or damaged.
- Continuity Test: Using a multimeter, we verify the “Normally Closed” (NC) circuit is closed and the “Normally Open” (NO) circuit is open in the resting state.
- Actuation Test: We press the button to ensure the contacts snap over cleanly—no chatter. Then we twist to release and verify the contacts reset.
- Seal Check: We inspect the O-ring and gasket integrity. If that seal is compromised, the IP69K rating is useless.
The Engineer’s Warning (Pitfalls)
Here is the most common mistake: Over-tightening the mounting nut.
Because this is a plastic (polycarbonate) housing, it doesn’t take much torque to crack the bezel or distort the internal sealing surface. I’ve seen maintenance guys use a wrench to crank this down as tight as a steel conduit fitting. Don’t do it. Hand-tighten it, maybe a quarter turn with a strap wrench if you must, but check the manual for torque specs. If you crack the housing, moisture gets in, freezes, and shatters the internal mechanism during the next cold start. Also, ensure your panel cut-out is clean; a jagged hole will chew up the gasket during installation.
Installation & Configuration Guide
Replacing an E-stop is critical for safety compliance. Do not rush this.
- Pre-Installation (Safety First)
⚠️ LOTO: Lockout/Tagout the main power to the machine. An E-stop is a safety device; testing it live before installation is dangerous.
⚠️ Verify Wiring: Check the schematic. This unit is 1NO+1NC. Most safety circuits use the NC contact for the safety loop and the NO for PLC monitoring. Ensure you wire the correct terminals. - Removal
- Disconnect the wiring from the old unit. Take a photo first!
- Unscrew the mounting ring/nut from the back.
- Pull the old unit out from the front. Clean the panel surface where the gasket sits.
- Installation
- Insert the new 1SFA619550R1071 through the 22.5mm hole.
- Secure it with the provided mounting hardware. Tighten gently until the gasket compresses and the unit is snug.
- Reconnect wires to the screw terminals. Ensure they are tight (vibration can loosen them).
- Power-On & Testing
- Restore power.
- Functional Test: Press the E-stop. The machine must stop immediately. Try to reset the machine (if possible)—it should not reset while the button is pressed.
- Reset Test: Twist the button to release. Verify the system allows a normal restart sequence.
Compatible Replacement Models
| Model Number | Compatibility | Notes |
|---|---|---|
| 1SFA619550R1071 | ✅ Drop-in | Exact replacement. Keep a spare of this exact number. |
| 1SFA619550R10xx | ⚠️ Contact Config | Other models in the R10xx series look identical but may have different contact arrangements (e.g., 2NC). Check the suffix carefully. |
| CE4T Series (Generic) | ❌ Hardware Mod | While mechanically similar, other manufacturers’ “40mm twist release” heads might not fit the ABB compact housing depth or thread pitch. Stick to OEM. |
Frequently Asked Questions (FAQ)
Q: What does the “1071” in the part number mean?
A: It defines the specific configuration. “10” usually refers to the contact arrangement code (1NO+1NC in this case), and “71” often refers to the color/bezel combination (Red/Black). Always verify the full string.Q: Can I use this outdoors?
A: Yes. With an IP66/IP67 rating, it is dust-tight and protected against temporary immersion. The polycarbonate housing is also UV resistant enough for outdoor use, unlike some ABS plastics that yellow and crack.Q: My button feels “mushy” or doesn’t click. Is it broken?
A: Likely. The internal spring mechanism or the contact block has worn out. Since this is a sealed “Compact” unit, you cannot open it to clean or repair the contacts. Replace the whole unit.Q: Does this come with the keys for locking?
A: No. This model (1SFA619550R1071) is a “Twist to Release” type. It does not use keys. If you need a key-release version, you are looking for a different part number (likely starting with CE4K…).Q: Is the 1NC contact safe for a Category 3 safety circuit?
A: A single NC contact is typically used for basic stopping. For Category 3 or PLd/PLe safety levels, you usually need redundant contacts (e.g., 2NC or 3NC) and monitored circuits. Check your risk assessment; you might need a different model with more contacts.
