Key Technical Specifications
| Parameter | Detail |
|---|---|
| Part Number | 810-800082-043 |
| Manufacturer | Lam Research |
| Product Type | VME breakout / interconnect PCB |
| Application | Lam Research semiconductor equipment control subsystem |
| Interface | VME system interconnect |
| Connector | 64-pin (verify pinout before installation) |
| Board Size | Approx. 222 × 112 × 10.2 mm |
| Operating Voltage | Verify with OEM datasheet; some listings cite 9–36 VDC |
| Operating Temperature | Verify with OEM datasheet; some listings cite −40 to 85 °C |
| Condition | New Surplus or Refurbished (Tested), subject to stock |
| Warranty | 12 months unless otherwise stated |
| Delivery | Anti-static packaging, label photos, test report if available |
Product Introduction
LAM 810-800082-043 is a Lam Research VME breakout / interconnect PCB used inside Lam semiconductor process equipment. It routes signals between VME modules, backplanes, and tool subsystems rather than acting as a standalone controller.This board is typically found in legacy Lam tool frames where VME-based control electronics manage I/O routing, module communication, and internal equipment signaling. Exact revision, connector pinout, and supported tool platform should be confirmed before replacement.
Installation & Configuration Guide
Preparation (10 min)
- Record tool ID, chamber, and fault history.
- Photograph the existing board label, revision, and cable routing.
- Verify the replacement revision matches the original.
- Prepare ESD strap, insulated tools, and clean workspace.
Removal (5–10 min)
- Power down the equipment following Lam lockout/tagout rules.
- Wait for capacitors and power rails to discharge.
- Label every cable before disconnecting.
- Remove mounting hardware and extract the board without forcing connectors.
Installation (10 min)
- Inspect connectors for bent pins or corrosion.
- Seat the board firmly into the VME slot or mounting position.
- Reconnect cables using the saved labels and photos.
- Confirm grounding straps and shielding are reinstalled.
Power-On & Test (10 min)
- Measure supply voltage before enabling full power.
- Power up in service mode if available.
- Check VME enumeration, communication status, and fault codes.
- Run a controlled functional test before returning to production.
Troubleshooting Quick Reference
| Symptom | Likely Cause | First Action |
|---|---|---|
| Tool does not recognize board | Wrong revision or loose seating | Reseat board; compare revision label |
| Communication timeout | Cable misroute or damaged harness | Recheck labeled cables; inspect connectors |
| Intermittent faults | Oxidized pins or loose fasteners | Clean contacts; torque mounting hardware |
| Overvoltage alarm | External supply or backplane issue | Measure supply rails before replacing board |
| Board fails after swap | Firmware/revision mismatch | Compare OEM revision and tool configuration |
Dimensions, Mounting & Wiring Notes
- Approximate dimensions: 222 × 112 × 10.2 mm.
- Mounting: VME slot or equipment-specific PCB bracket.
- Connector: 64-pin interface; pinout must match the original assembly.
- Wiring: Do not force connectors. Misaligned pins can damage the backplane.
- ESD: Handle as a static-sensitive assembly at all times.
FAQ
Is 810-800082-043 a CPU or power supply?
No. It is a VME breakout / interconnect PCB for Lam Research equipment, not a processor or power module.Can I use any 810-800082 board as a replacement?
Not automatically. Revision, connector layout, and tool platform must match. Even small suffix changes can affect compatibility.Do you ship this as new or tested?
Condition depends on current stock. Available options typically include New Surplus or Refurbished (Tested). Confirm before ordering.What if my tool shows a VME communication fault after replacement?
Check board revision, cable labels, connector seating, and backplane slot first. Most post-swap issues come from wiring or revision mismatch.I only have a partial photo of the old board. Can you still quote it?
Send whatever you have. Without a clear revision label and connector photo, we will treat it as “pending verification” rather than quoting immediately.Is this part still made by Lam Research?
It is generally treated as a discontinued or legacy spare. Availability depends on surplus and tested inventory.
