Key Technical Specifications
- Manufacturer: VIBRO-METER (Meggitt)
- Dynamic Channels: 16 independent channels
- Tachometer Channels: 4 speed/phase channels
- Signal Type: Differential signal inputs
- Communication: Ethernet (8P8C / RJ45) for VibroSight software
- Module Pairing: XMV16 or XMC16 (installed directly behind)
- Rack Compatibility: VM600 ABE04x system rack (rear mounting)
- Configuration: All channels independently configurable
- Software Integration: Designed for VibroSight platform
- Part Number: 200-565-000-013
Product Introduction
VIBRO-METER VM600 IOC16T is a high-reliability input/output interface module designed for the VM600 Mk2 mechanical monitoring system. It provides the critical physical interface between field vibration sensors and the system’s processing modules.This module supports 16 dynamic channels and 4 tachometer channels with differential signal inputs. It mounts directly behind the corresponding XMV16 or XMC16 processing module in the VM600 rack, forming a matched card pair that ensures signal integrity and system reliability.
Installation & Configuration Guide
Preparation
Verify the VIBRO-METER VM600 IOC16T matches your system requirements. Confirm you have the matching XMV16 or XMC16 processing module. Ensure the VM600 ABE04x rack power is off before installation.Removal
Power down the VM600 rack completely. Disconnect all field wiring from the IOC16T terminal blocks. Remove the mounting screws securing the module to the rear of the rack. Carefully extract the module from the backplane connector.Installation
Position the VIBRO-METER VM600 IOC16T in the rear slot directly behind the XMV16/XMC16 processing module. Align the backplane connector and slide the module in until fully seated. Secure with mounting screws. Reconnect all field wiring according to the loop diagram.Power-On & Test
Restore power to the VM600 rack. Verify the module LEDs indicate normal operation. Launch VibroSight software and confirm communication via the RJ45 Ethernet connection. Check that all 16 dynamic channels and 4 tachometer channels are recognized and reporting valid data.
Troubleshooting Quick Reference
- No Communication: Check RJ45 Ethernet cable connection. Verify IP configuration in VibroSight software.
- Channel Fault LED: Inspect field wiring for open circuits or shorts. Verify sensor compatibility and wiring polarity.
- Invalid Data Readings: Confirm differential signal wiring is correct. Check sensor sensitivity configuration in VibroSight.
- Module Not Recognized: Reseat the IOC16T module in the backplane. Verify it is paired with the correct XMV16/XMC16 module.
- Intermittent Faults: Check for loose terminal connections. Inspect backplane connector for corrosion or damage.
Dimensions, Mounting & Wiring Notes
- Dimensions: Standard VM600 rear-mount module form factor
- Mounting: Rear of VM600 ABE04x rack, directly behind XMV16/XMC16
- Wiring: 16 dynamic sensor inputs + 4 tachometer inputs on dedicated terminal blocks. RJ45 Ethernet port for VibroSight communication.
FAQ
Can I use this IOC16T with other VM600 processing modules?
No. The IOC16T is specifically designed to pair with XMV16 or XMC16 processing modules only. It must be installed directly behind one of these modules to form a functional card pair.I received the module, but the part number suffix differs. What now?
Stop. The 200-565-000-013 suffix indicates specific hardware revision and compatibility. Different suffixes may have incompatible firmware or connector configurations. Contact us immediately with your order number and the exact part number from your existing module.Is this a refurbished unit?
No. This is New Original (New Surplus) stock. It has never been installed in a field system. We perform full functional testing before shipment to verify all channels operate correctly.What’s the lead time if it’s not in stock?
Typically 3-5 business days from our warehouse. We maintain strategic inventory for critical VM600 spares. Expedited shipping is available for emergency shutdown situations.How do I know this isn’t a counterfeit?
Every unit includes a traceable serial number and original Meggitt/Vibro-Meter labeling. We verify against manufacturer records. You can request photos of the actual unit before purchase, including the label and PCB.Will my existing VibroSight configuration work with this replacement?
Yes, if the part number matches exactly. The IOC16T is a hardware interface module; configuration resides in the XMV16/XMC16 processing module and VibroSight software. We recommend backing up your current configuration before replacement.I installed it but VibroSight can’t communicate. Help?
First, check the RJ45 Ethernet cable and link lights. Then verify the module IP address matches your network configuration. Finally, confirm the module is properly seated and paired with the correct processing module.
