Description
Key Technical Specifications
| Parameter | Value |
|---|---|
| Product Type | RS-485 / fieldbus network terminator |
| Brand | ABB |
| Model | NTR002-A |
| Primary Application | End-of-line termination for RS-485 segments |
| Supported Protocols | PROFIBUS DP, Modbus RTU, generic RS-485 |
| Power Requirement | Passive; typically no external supply |
| Mounting | DIN rail or panel mount, depending on variant |
| Typical Use | ABB DCS cabinets, drive systems, remote I/O, robot cells |
| Condition | Surplus / spare; verify labeling and packaging |
| Documentation | Confirm with OEM datasheet and site wiring drawings |
Product Introduction
I’ve walked enough plants to know that half of “mysterious” RS-485 faults are not the master, not the slave, and not the cable. They’re reflections. Someone leaves the far end unterminated, a VFD ramps up, and suddenly nodes drop, retries spike, and the night shift gets paged. The ABB NTR002-A is the boring part that prevents that mess. It sits at the end of an RS-485 or fieldbus segment and keeps the line impedance matched so the bus stays quiet.Engineers don’t buy this because it’s fancy. They buy it because a missing terminator can turn a clean Modbus RTU loop into a diagnostic nightmare. It’s passive, small, and easy to stock. If your ABB panel has intermittent “node lost” alarms or bus errors that appear when motors start, check the far end of the segment first. This is the kind of component that costs almost nothing compared with the downtime it prevents.
Quality SOP & Tech Pitfalls
The Lab Report (SOP)
- Visual and counterfeit check — label, housing, terminals, and mounting hardware inspected.
- Continuity and resistance check — verified with a Fluke 115 or equivalent multimeter.
- Live bus check — installed at the end of a test RS-485 segment to confirm stable communication.
- Insulation check — basic insulation and short-circuit verification before packing.
- Final logging — model, batch/lot, photos, and condition recorded before anti-static sealing.
The Engineer’s Warning (Pitfalls)
- Do not install a terminator in the middle of an RS-485 daisy chain. It belongs at the physical end of the segment. Put it in the wrong spot and you’ll kill communication for everything downstream.
- Don’t assume “NTR002-A” is interchangeable with every ABB bus accessory. Some listings mix it up with analog modules, terminal boards, or unrelated parts. Verify the label and the actual hardware before wiring.
- I once chased a PROFIBUS fault for hours because someone had added a second terminator near the master. The bus looked fine on paper. In reality, double termination was distorting the signal. One end, one terminator.
Installation & Configuration Guide
- Pre-Installation
- ⚠️ De-energize the control circuit before working on bus wiring.
- Identify the physical end of the RS-485 segment.
- Photograph existing wiring, node addresses, and terminator positions.
- Removal
- Label the A/B or +/− bus conductors.
- Disconnect the unterminated end cleanly.
- Remove any incorrect or damaged terminator.
- Installation
- Install the NTR002-A only at the last node of the RS-485 segment.
- Connect shielded twisted-pair bus wiring according to site drawings.
- Seat the terminator firmly on DIN rail or panel mount.
- Ensure the shield is grounded at one point only, unless the site standard says otherwise.
- Power-On & Testing
- Restore power to the bus devices.
- Check node discovery and communication status.
- Verify no “node lost,” timeout, or retry alarms.
- Run a short communication test under normal load, including VFD starts if applicable.
Compatible Replacement Models
- ✅ Drop-in Replacement: Another ABB NTR002-A with matching mechanical and electrical configuration. Confirm labeling and termination type before swapping.
- ⚠️ Software/Bus Compatible: Standard RS-485 terminators with the correct impedance may function on the same bus, but wiring, mounting, and site standards must be verified. Expect minor rework.
- ❌ Hardware Mod Required: Generic termination networks built into connectors, DIN-rail terminators with different pinouts, or protocol-specific PROFIBUS terminators that do not match the site wiring should not be forced in without a full segment review.
Frequently Asked Questions (FAQ)
Q: Is the ABB NTR002-A an analog I/O module?
No. Based on available market documentation, it is commonly listed as an RS-485 / fieldbus network terminator. Some third-party listings mislabel it as an analog module, so always verify the physical unit.Q: Can I install it anywhere on the RS-485 bus?
No. It belongs at the physical end of the segment. Installing it mid-bus will usually cause communication failures.Q: Does it need external power?
Typically no. It is a passive termination device. Confirm with the actual unit and OEM documentation.Q: Will it work on Modbus RTU and PROFIBUS DP?
In many ABB RS-485 applications, yes. But the exact compatibility depends on the bus wiring, impedance, and site standard. Check the segment design before installing.Q: Is this still available as new original stock?
Availability varies by supplier. Most units in the market are surplus, spare, or verified stock. Treat “new” claims with caution unless packaging and labeling are confirmed.Q: Can I use it to fix intermittent node dropouts?
Often, yes—if the root cause is missing or incorrect end termination. If the problem is noise, grounding, cable damage, or a bad node, a terminator alone will not fix it.Q: What warranty can I expect?
Many surplus suppliers offer around 12 months, but that depends on the seller. Always confirm warranty, return policy, and test support before purchase.




Tel:
Email:
WhatsApp: 
